Medium-Pressure Blowers for Large Inflatables

More pressure for large structures, long ducts and demanding internal airflow paths.

Medium-Pressure Blowers for Large Inflatables focuses on large leisure inflatables, long tunnels, giant arches, tall structures, remote ducts and multi-branch installations. It uses medium-pressure centrifugal blower with reinforced housing and a motor selected for sustained pressure to match the airflow behavior to the product rather than forcing one generic fan across unrelated inflatable forms. Bridge the gap between small portable blowers and industrial process equipment.

The core website envelope is approximately 0.75-3.0 kW for the main website range, 800-3,000 m³/h at the installed operating point and 2.4-5.0 kPa. These numbers are presented as a selection range, not as a guaranteed model. The final duty point must be confirmed after voltage, frequency, altitude, ambient temperature, duct geometry, fabric leakage and operating hours are known.

Product and Engineering Snapshot

Parameter note: all values are representative engineering envelopes, not a promise for every model. Final selection must be confirmed against the performance curve at the actual voltage, frequency, altitude, ambient temperature, duct length, outlet geometry and required operating pressure.

Product Positioning and Customer Value

Bridge the gap between small portable blowers and industrial process equipment. The solution should solve a visible operating problem: soft or unstable fabric, slow recovery, excessive noise, awkward installation, repeated overheating, too many incompatible spare parts, or long deployment time.

Value 1. Maintains meaningful airflow at several kilopascals of system resistance.

Value 2. Supports longer ducts that move noise and equipment away from users.

Value 3. Allows pressure-based commissioning, VFD control and redundancy.

Application-specific integration. Bridge the gap between small portable blowers and industrial process equipment. This creates a clearer path from the inflatable requirement to a serviceable product package.

Where This Page Creates Value

Representative use patterns include Large leisure, Giant arch, Remote stage, Shelter and Multi-branch. Each application changes the balance between airflow, static pressure, noise, installation space and service access. For this reason, the application list should be used as a routing guide: the final blower recommendation follows the actual inlet, duct and prototype pressure behavior.

· Large leisure: high leakage and repeated deformation. The selection should be confirmed against the complete installed resistance and duty.

· Giant arch: long path and wind-exposed surface. The selection should be confirmed against the complete installed resistance and duty.

· Remote stage: long duct and acoustic separation. The selection should be confirmed against the complete installed resistance and duty.

· Shelter: multiple air beams. The selection should be confirmed against the complete installed resistance and duty.

· Multi-branch: controlled manifold and standby option. The selection should be confirmed against the complete installed resistance and duty.

Representative Application Case

A large obstacle product uses two small mismatched blowers but one section stays soft.

A large obstacle product uses two small mismatched blowers but one section stays soft. The case is intentionally representative rather than tied to an original equipment source. It shows how the product page can translate a customer scenario into a practical engineering recommendation.

Challenge: Both units operate near their pressure limit and the branch layout is unbalanced.

Customer value: The operator gains uniform inflation and simpler cable management.

The case parameters are a starting envelope. During prototype validation, check the shape at the highest and most remote zones, measure internal pressure where possible, record motor current after warm-up and confirm that the intake, discharge and electrical connections remain accessible.

Engineering and Selection Notes

· Treat the inflatable, connecting duct and blower as one air system. A high free-air number alone does not guarantee adequate pressure after bends, filters, valves, long hoses or restrictive inlets.

· Check 50 Hz and 60 Hz performance separately. Motor speed, airflow, static pressure, current and temperature rise can change with frequency and supply voltage.

· Allow an altitude and hot-weather margin. Lower air density reduces mass flow and cooling capacity, so elevated or hot installations may require derating or a larger blower.

· For outdoor use, distinguish weather-resistant construction from fully waterproof construction. Keep connections above standing water, use locally suitable ground-fault protection and inspect cords before deployment.

· Confirm the continuous-duty rating, thermal protection and allowable outlet temperature whenever the blower will run for long periods.

Available Customization

0.75-3.0 kW • 2.4-5.0 kPa class • multi-speed or VFD • portable or skid frame • metal / polymer housing • pressure sensor • weather package • duty/standby manifold

For OEM programs, available work can include outlet matching, housing or base layout, cable and plug selection, switch and speed-control design, labeling, packaging, service parts, sample approval and production test planning. Compliance documents must be tied to the exact final configuration.

Design responsibility note: blower sizing must be validated as part of the complete inflatable system. For occupied, ride-on, rescue, tent or other safety-critical inflatables, the finished product must also follow the applicable local product, electrical, anchoring, fire and operational requirements.