Integrated Blower, Lighting and Mobile Bases

Combine air, light, control and transport in one event-ready chassis.

Integrated Blower, Lighting and Mobile Bases focuses on integrated bases for inflatable columns, tube dancers, visual display tubes and mobile promotional installations. It uses compact vortex / centrifugal chassis for pressure-sensitive columns and axial bases for high-volume dancing motion to match the airflow behavior to the product rather than forcing one generic fan across unrelated inflatable forms. Reduce loose components by integrating blower, LED, control, cable management, handles and casters.

The core website envelope is approximately 100-750 W for pressure chassis; 0.5-1.5 HP for axial dancer bases, 100-550 m³/h for pressure chassis; 3,500-10,000 m³/h for axial bases and 0.5-1.9 kPa for pressure chassis; low-static open-volume duty for axial bases. These numbers are presented as a selection range, not as a guaranteed model. The final duty point must be confirmed after voltage, frequency, altitude, ambient temperature, duct geometry, fabric leakage and operating hours are known.

Product and Engineering Snapshot

Parameter note: all values are representative engineering envelopes, not a promise for every model. Final selection must be confirmed against the performance curve at the actual voltage, frequency, altitude, ambient temperature, duct length, outlet geometry and required operating pressure.

Product Positioning and Customer Value

Reduce loose components by integrating blower, LED, control, cable management, handles and casters. The solution should solve a visible operating problem: soft or unstable fabric, slow recovery, excessive noise, awkward installation, repeated overheating, too many incompatible spare parts, or long deployment time.

Value 1. Matches the airflow technology to either upright shape or animated movement.

Value 2. Combines outlet, stability, mobility, lighting and controls in one deployable module.

Value 3. Reduces setup errors through a direct fabric collar and standardized chassis.

Application-specific integration. Reduce loose components by integrating blower, LED, control, cable management, handles and casters. This creates a clearer path from the inflatable requirement to a serviceable product package.

Where This Page Creates Value

Representative use patterns include RGBW column, Illuminated dancer, Wayfinding pillar, Stage scenic and Roadshow. Each application changes the balance between airflow, static pressure, noise, installation space and service access. For this reason, the application list should be used as a routing guide: the final blower recommendation follows the actual inlet, duct and prototype pressure behavior.

· RGBW column: pressure chassis with upward illumination. The selection should be confirmed against the complete installed resistance and duty.

· Illuminated dancer: axial base and protected light. The selection should be confirmed against the complete installed resistance and duty.

· Wayfinding pillar: blower, light and branded sleeve. The selection should be confirmed against the complete installed resistance and duty.

· Stage scenic: remote interface and low profile. The selection should be confirmed against the complete installed resistance and duty.

· Roadshow: stackable base and flight case. The selection should be confirmed against the complete installed resistance and duty.

Representative Application Case

Twelve 3 m RGBW columns must deploy in under one hour.

Twelve 3 m RGBW columns must deploy in under one hour. The case is intentionally representative rather than tied to an original equipment source. It shows how the product page can translate a customer scenario into a practical engineering recommendation.

Challenge: Separate fan and light equipment produces tangled cables and inconsistent light position.

Customer value: The team gains faster setup and uniform inflation and lighting.

The case parameters are a starting envelope. During prototype validation, check the shape at the highest and most remote zones, measure internal pressure where possible, record motor current after warm-up and confirm that the intake, discharge and electrical connections remain accessible.

Engineering and Selection Notes

· Treat the inflatable, connecting duct and blower as one air system. A high free-air number alone does not guarantee adequate pressure after bends, filters, valves, long hoses or restrictive inlets.

· Check 50 Hz and 60 Hz performance separately. Motor speed, airflow, static pressure, current and temperature rise can change with frequency and supply voltage.

· Allow an altitude and hot-weather margin. Lower air density reduces mass flow and cooling capacity, so elevated or hot installations may require derating or a larger blower.

· For outdoor use, distinguish weather-resistant construction from fully waterproof construction. Keep connections above standing water, use locally suitable ground-fault protection and inspect cords before deployment.

· Confirm the continuous-duty rating, thermal protection and allowable outlet temperature whenever the blower will run for long periods.

· Combined fan-and-light bases need separate thermal checks for the motor, LED source and driver at maximum ambient temperature.

· Base stability and fabric attachment must be considered independently from airflow; casters should be secured during operation.

Available Customization

9 / 12 / 18 inch outlet • custom base size • integrated LED • caster and handle • single or multi-speed • protected motor option • custom color • flight case

For OEM programs, available work can include outlet matching, housing or base layout, cable and plug selection, switch and speed-control design, labeling, packaging, service parts, sample approval and production test planning. Compliance documents must be tied to the exact final configuration.

Design responsibility note: blower sizing must be validated as part of the complete inflatable system. For occupied, ride-on, rescue, tent or other safety-critical inflatables, the finished product must also follow the applicable local product, electrical, anchoring, fire and operational requirements.